MODEL H260
CYLINDER H260
Type | Size | Maximum Taper | Above Block |
Wet Sleeve | 3.877 | .008 | .004 |
- | 3.875 | - | .0015 |
PISTON H260
Pin Hole Diameter | Ring Groove Diameter | Ring Groove Width | Fit In Cylinder Bore | ||||||
1st | 2nd | 3rd | 4th | 1st | 2nd | 3rd | 4th | ||
1.2500 | 3.497 | 3.497 | 3.497 | 3.457 | .129 | .128 | .128 | .253 | .003X1/2"Gage |
1.2498 | 3.487 | 3.487 | 3.487 | 3.447 | .128 | .127 | .127 | .252 | 5-10 lbs. |
Diameter At Top Of Piston | Diameter At Bottom Of Piston | ||||||||
A | AA | B | BB | C | A | AA | B | BB | C |
3.87105 | 3.87155 | 3.87205 | 3.87255 | 3.87305 | 3.8723 | 3.8728 | 3.8733 | 3.8738 | 3.8743 |
PISTON PIN H260
Pin Diameter | Diameter Hole In Rod | Finished Bushing Diameter |
Pin Fit In Piston |
Clearance In Bushing |
|
Possible |
Desired |
||||
1.2500 | 1.3753 | 1.2504 |
Lite Push Fit With Piston Heated To 160°F |
.0002 | .0004 |
1.2498 | 1.3743 | 1.2502 | .0006 | - |
PISTON RINGS H260
Type Of Ring | Groove Position | Width | Thickness | Gap Clear | Side Clear |
Plain | 1 | .124 | .167 | .017 | .006 |
Compression | .123 | .157 | .009 | .004 | |
Taper Face | 2 | .124 | .167 | .017 | .005 |
Compression | .123 | .157 | .009 | .003 | |
Taper Face | 3 | .124 | .167 | .017 | .005 |
Compression | .123 | .157 | .009 | .003 | |
Ventilated | 4 | .249 | .167 | .017 | .0045 |
Oil | .2485 | .157 | .009 | .003 |
VALVE GUIDE H260
Outside Diameter | Stem Hole Diameter | Valve Seat Face To Top Of Guide | Valve Stem Clearance Limits |
Desired Stem Clearance |
||||
Intake |
Exhaust | Reamed | Intake | Exhaust | Intake | Exhaust | Intake | Exhaust |
.752 | .752 | .4365 | 1 9/32 | 1 9/32 | .0021 | .005 | .0015 | .004 |
.751 | .751 | .4360 | - | - | .0008 | .0035 | - | - |
INTAKE VALVE H260
Stem Diameter | Maximum Stem Wear | Minimum Margin | Face Angle | Clearance Limits | Desired Clearance |
.4352 | .002 | 1/32 | 30° | .0021 | .0015 |
.4344 | - | - | - | .0008 | - |
EXHAUST VALVE H260
Stem Diameter | Maximum Stem Wear | Minimum Margin | Face Angle | Clearance Limits | Desired Clearance |
.4325 | .002 | 1/32 | 44° | .005 | .004 |
.4315 | - | - | - | .0035 | - |
VALVE SEAT (INTAKE) H260
Seat Angle | Seat Width | Stone Size | Narrow Stone | Stone Diameter |
30° | 3/32 | 30° | 15°-70° | 1 3/4 |
VALVE SEAT (EXHAUST) H260
Seat Angle | Seat Width | Stone Size | Narrow Stone | Stone Diameter |
45° | 3/32 | 45° | 15°-70° | 1 5/8 |
VALVE SPRING H260
Free Length |
Valve Closed |
Valve Open |
||
Spring Length | Spring Load | Spring Length | Spring Load | |
2 3/8 | 1 7/8 | 64-58 lbs. | 1.521 | 123-115 lbs. |
CAMSHAFT H260
Bearing Journal Diameter |
Tappet Hole Diameter |
Tappet Diameter |
Clearance Limits |
End Play |
||
Front | Center | Rear | ||||
1.9965 | 1.7465 | 1.684 | 1.0005 | .9985 | .003 | .009 |
1.9960 | 1.7460 | 1.6835 | 1.0000 | .9975 | .0015 | .005 |
CAMSHAFT BEARINGS H260
Inside Diameter |
Clearance Limits |
Oil Pump Backlash |
||||
1 | 2 | 3 | 1 | 2 | 3 | |
2.000 | 1.750 | 1.6875 | .0004 | .004 | .004 | .010 |
1.999 | 1.749 | 1.6865 | .0025 | .0025 | .0025 | .008 |
CONNECTING ROD H260
Side Play |
Bearing Journal Size |
Bearing Clearance |
Desired Clearance |
|
Possible | Desired | |||
.006 | .008 | 2.500 | .0025 | .0015 |
.010 | - | - | .0005 | - |
CRANKSHAFT H260
Thrust On Front Main Bearing |
End Thrust |
Bearing Journal Size |
Bearing Clearance |
Desired Clearance |
Flywheel RunOut |
.008 | 2.874 | .0027 | .0015 | .008 | |
.005 | 2.873 | .0005 | - | - |
All Contents Copyright © 2006,
MasseyBoard.Com. All Rights Reserved
Created by: Juniors Computer Sales & Service
Direct All Comments to: Web Master